projekte:2018:cnc-mill
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende ÜberarbeitungLetzte ÜberarbeitungBeide Seiten der Revision | ||
projekte:2018:cnc-mill [2019/10/03 12:45] – [CNC-Fräse Isel ICV] f_cnyrim | projekte:2018:cnc-mill [2019/10/03 14:07] – f_cnyrim | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
- | ====== CNC-Fräse Isel ICV ====== | + | ====== CNC-Fräse Isel ICV Laufende Projekte |
Schaubstock Sorrotec: | Schaubstock Sorrotec: | ||
Zeile 20: | Zeile 20: | ||
1x[[https:// | 1x[[https:// | ||
- | 7x [[https:// | + | 3x [[https:// |
- | 4x [[https:// | + | 2x [[https:// |
1x [[https:// | 1x [[https:// | ||
Zeile 28: | Zeile 28: | ||
Vakumpumpe: | Vakumpumpe: | ||
- | 1x [[https:// | + | 1x T stück in 1/2" |
+ | |||
+ | [[https:// | ||
+ | |||
+ | 2x [[https:// | ||
+ | |||
+ | 1x 8mm Schlauch (blau) | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | 1x 1/2 gewinde und 8mm Schlauch + 1x 1/2 gewinde und 6mm Schlauch | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | 1x 8mm auf 6mm | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | 2x Tstück 6mm | ||
+ | |||
+ | https:// | ||
Sonstiges: | Sonstiges: | ||
Zeile 36: | Zeile 56: | ||
[[https:// | [[https:// | ||
- | 4x Reduziersück 1/2" auf 1/8" | + | 3x Reduziersück 1/2" auf 1/8" |
[[https:// | [[https:// | ||
- | 2x Drossel Für MMS (einmal für den KSS Tank eimal für tägerluft) | + | 1* 6mm fitting |
+ | |||
+ | [[https:// | ||
+ | |||
+ | 2x Drossel Für MMS (einmal für den KSS Tank eimal für tägerluft) | ||
[[https:// | [[https:// | ||
- | 2x KSS Schlauchfiting | + | 4x KSS Schlauchfiting |
+ | |||
+ | [[https:// | ||
+ | |||
+ | 1x Schaluch 4mm (Klar) | ||
- | https:// | + | [[https:// |
1x flow einstellung KSS | 1x flow einstellung KSS | ||
Zeile 54: | Zeile 82: | ||
Klemmen für den schrabstock bitte nochmal nach günstigeren suchen!: | Klemmen für den schrabstock bitte nochmal nach günstigeren suchen!: | ||
- | <font inherit/ | + | <font inherit/ |
[[https:// | [[https:// | ||
Zeile 65: | Zeile 93: | ||
[[https:// | [[https:// | ||
- | |||
====== Wunschliste ====== | ====== Wunschliste ====== | ||
Zeile 183: | Zeile 210: | ||
|Gewindefräser (nicht gantz einfach zu benutzen)|[[https:// | |Gewindefräser (nicht gantz einfach zu benutzen)|[[https:// | ||
- | ===== Materialien ===== | + | ^ ^ ^ | |
- | + | | | | | | |
- | ^Material^Größe^Fräser| | + | |
- | |[[https:// | + | |
| | | | | | | | | | ||
projekte/2018/cnc-mill.txt · Zuletzt geändert: 2019/10/04 20:48 von f_cnyrim