Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- projekte:minifraese:assembly_frame [2015/10/29 11:29] – sven
+++ projekte:minifraese:assembly_frame [2015/11/27 23:22] (aktuell) – Externe Bearbeitung 127.0.0.1
@@ Zeile 9: / Zeile 9: @@
     * 8 x mcs_l-verbinder_stabil_60x60
     * 4 x mcs_endkappe_40x20
-    * 10 x mcs_winkel_stabil_40x20
+    * 12 x mcs_winkel_stabil_40x20
     * 2 x mcs_wuerfelverbinder_20x20
     * 2 x mcs_endkappe_60x20
-  * 116 x Screws (DIN 7984)
+  * 124 x Screws (DIN 7984)
-    * (7 x 8) x //M5x20mm// (for mcs_l-verbinder_stabil_60x60)
+    * (7 x 8) x //M5x10mm// (for mcs_l-verbinder_stabil_60x60)
-    * (2 x 4) x //M5x20mm// (for mcs_endkappe_40x20)
+    * (2 x 4) x //M5x10mm// (for mcs_endkappe_40x20)
-    * (4 x 10) x //M5x20mm// (for mcs_winkel_stabil_40x20)
+    * (4 x 12) x //M5x8mm// (for mcs_winkel_stabil_40x20)
-    * (3 x 2) x //M5x20mm// (for mcs_wuerfelverbinder_20x20)
+    * (3 x 2) x //M5x8mm// (for mcs_wuerfelverbinder_20x20)
-    * (3 x 2) x //M5x20mm// (for mcs_endkappe_60x20)
+    * (3 x 2) x //M5x10mm// (for mcs_endkappe_60x20)
-  * 102 x Slot Nuts (M5 I-Type slot 5)
+  * 110 x Slot Nuts (M5 I-Type slot 5)
     * (5 x 8) x //M5 I-Type slot 5// (for mcs_l-verbinder_stabil_60x60)
-    * (4 x 10) x //M5 I-Type slot 5// (for mcs_winkel_stabil_40x20)
+    * (4 x 12) x //M5 I-Type slot 5// (for mcs_winkel_stabil_40x20)
     * (3 x 2) x //M5 I-Type slot 5// (for mcs_wuerfelverbinder_20x20)
@@ Zeile 31: / Zeile 31: @@
   - add angle connectors (mcs_winkel_stabil_40x20) to support the new struts
   - connect third horizontal bar to the just build rectangle 120mm from the rear horizontal extrusion using angle connectors (mcs_winkel_stabil_40x20)
+  - add end covers (mcs_endkappe_40x20) to the sides of the foremost and hindmost extrusions
 ==== Vertical Frame ====
+  - combine 3 extrusion (300mm) to form a "U"-Form using angle connectors (mcs_winkel_stabil_40x20)
+  - reinforce using corner connectors (mcs_l-verbinder_stabil_60x60)
+  - add end covers (mcs_endkappe_60x20) to the "bottom" of the "U"
 ==== Connect everything ====
-  - add 2 vertical extrusion (300mm) to the new horizontal one with cube connectors (mcs_wuerfelverbinder_20x20)
+  - connect the vertical frame (invert the "U") with the lower frame using cube connectors (mcs_wuerfelverbinder_20x20)
-  - add angle connectors (mcs_winkel_stabil_40x20) to stengthen the connection
+  - add angle connectors (mcs_winkel_stabil_40x20) to strengthen the connection between the long struts (400mm) and the vertical frames "legs"
-  - add corner connectors (mcs_l-verbinder_stabil_60x60)
+  - add corner connectors (mcs_l-verbinder_stabil_60x60) to finalize
-  -
+==== Protokoll Cafe Europa ====
+ * [[projekte:minifraese:protocol_frame|Protokoll]]